Hydronic Heat Not Working in Novato? Restarting a Shut-Down Boiler
A Novato hydronic baseboard system sprang a leak when it was turned back on after sitting shut down. Here's how we got it running safely, step by step, and what to check before you restart your own boiler.

Novato isn't known for boilers. Most homes here heat with forced air, but plenty of houses still have hot-water baseboard or radiant heat, and some of those systems sit shut down for a season or longer. When the cold arrives and someone flips them back on, problems that were hiding show up all at once. If your Novato boiler won't run, call or text Local Plumbing at (415) 234-0370.
Here's a real job from October, done in two careful steps, and what to check before you restart a system that's been off.
A Real Novato Job: Two Steps to Bring a Boiler Back
Step 1: The leak
A Novato homeowner turned their hydronic heating back on after it had been shut down, and a pipe started leaking. We:
- Repaired the leaking 1/2-inch copper heating pipe with ProPress press fittings and Type L copper. No soldering, so no open flame near the house framing.
- Pressure-tested the repair to confirm it was watertight.
- Ran a full system startup, bleeding the air out of every zone and baseboard loop.
- Checked system pressure and circulation to see whether the boiler could safely run.
We were upfront that this first step might not restore the heat by itself. It was about making the system safe to test.
Step 2: The safety control
The diagnostics found the next problem: the boiler's low-water cut-off had failed. That's the safety device that shuts the boiler down if the water level drops too low, which protects the heat exchanger from firing dry. With it failed, the boiler couldn't run.
We replaced the sensor with a correctly rated part, confirmed the water level, made sure the low-water shut-off worked, and tested the boiler through a full start-up.
Doing it in steps kept the homeowner in control. Each step was quoted and approved before we did it, and no money went into parts until we knew what the system actually needed.
Why Restarting an Idle Boiler Causes Problems
A hydronic system that sits off doesn't stay frozen in time:
- Pressure drops. Small leaks and weeping air vents let water out slowly. A system that should sit around 12 to 15 PSI cold may be near zero.
- Air collects. Air in the loops blocks circulation, so radiators or baseboards stay cold and the system gurgles.
- Pumps seize. Circulators that haven't turned in months can stick, especially in older systems with sediment.
- Weak joints fail. When the system heats up and pressure comes back, an old joint or a corroded section of pipe can start leaking, as it did on this job.
- Safety controls act up. Low-water cut-offs, pressure switches and flame sensors can fail or trip after a long shutdown.
Before You Turn Your Boiler Back On
If your system has been off for a while:
- Check the pressure gauge. If it reads near zero, don't fire the boiler. It needs water and a check for leaks first.
- Look for old water stains under pipes, valves and baseboards.
- Listen when it starts. Gurgling means air. Banging or kettling can mean poor flow or scale in the heat exchanger.
- Watch for an error code or lockout, and don't keep resetting it. Repeated lockouts point to a real problem.
- If anything was ever flooded, especially the gas valve or controls, don't relight it. Those parts need to be replaced.
Novato Homes and Hydronic Heat
Novato grew fast after World War II, and the median home dates to the mid-1970s. That means systems of very different ages. Some older homes kept their original boilers and baseboard. Others had radiant or hydronic heat added in remodels. Around Hamilton, the 1930s officers' quarters were originally built with basement boiler rooms and cast-iron radiators.
Novato also gets colder than southern Marin, with about a dozen frost nights a year. A boiler that's been ignored all summer tends to get its first real test on one of those mornings.
Repair or Replace?
Most restart problems are repairs: a leak, a failed control, a stuck pump, air in the lines. Replacement makes sense when the boiler is near the end of its life, the heat exchanger is failing, or parts aren't available anymore. For reference, a high-efficiency boiler replacement runs $8,500 to $15,000, and pump, manifold and valve upgrades typically run $1,200 to $4,500. Repairs are priced after we diagnose. See our boiler repair page and boiler replacement page.
New gas boilers can still be installed in the Bay Area. Under the Air District's rule as amended in November 2026, the zero-NOx requirement applies to home boilers manufactured after January 1, 2033.
Novato Boiler FAQs
Why won't my boiler start after being off all summer?
The most common causes are low system pressure, air in the lines, a stuck circulator pump or a safety control like a low-water cut-off that has failed or tripped.
What does a low-water cut-off do?
It shuts the boiler off if the water level drops too low, so the boiler can't fire with too little water in it. If it fails, the boiler won't run until it's replaced.
Is it safe to add water to my boiler myself?
Many systems have an automatic fill valve. If the pressure keeps dropping, there's a leak somewhere, and adding water only hides it. Have it checked.
Do you work on older hydronic baseboard systems?
Yes. We repair and replace boilers, baseboard, radiators and radiant floor systems across Novato and the rest of Marin and Sonoma.
Boiler Repair Across Novato
We repair hydronic and radiant heating across Novato, from Old Town and Hamilton to San Marin, Indian Valley, Ignacio and Bel Marin Keys, from our shop and training facility in San Rafael. Licensed C-16 & C-36, Lic #1091739. Call or text (415) 234-0370 or contact us. More on our Novato plumbing services and our boiler and radiant heating work.







































